You can find products similar to this one for sale below. Kinda grasping at straws here, but it could just be that there’s some setting that works fine on the TBird, but not on the newer CPU for whatever reason. By reading this site you agree to our cookie policy. The fan keeps the Northbridge cooler and adds stability at the higher bus speeds offered on the newer boards. Recently they opened the second work of the company in Mainland, China and the total output of these both works amounts approx thousand boards a month. If the card has both slots then it can use both signaling voltages.

Uploader: Dill
Date Added: 27 September 2018
File Size: 66.18 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 38266
Price: Free* [*Free Regsitration Required]

AGP4x + VIA Chipsets Fix

That card would work correctly in an AGP 3. I don’t take any chances with this board it133a more. The first main assembly line and the head office are located there.

Fast spreading out of DDR chipsets is limited by lots of factors: I doubt it had any circuitry to prevent damage if you inserted a 3. If you try to insert a card without a 3. I’m not sure exactly what causes the problem but apparently the motherboard and the video card are incompatible in some way which prevents Windows from properly assigning memory addresses to the video card.

But even if the signaling voltages are compatible, there are other things which can occasionally go wrong when you plug the card into the motherboard. If they both support 2x then they will run at 2x. If you would like to know what kind of video card is in your computer, open the “Control Panel” and double-click “Display” to bring up the “Display Properties” window.


Below I put the figures I think quite important while overclocking:. BioShock Infinite and Metro: Those are very rare but they happen. There are a few motherboards which do not use the correct AGP connector. This one is by Gainward, and a review can be found here – http: Did you clear CMOS after installing the new chip?

Perhaps they didn’t want to go to the trouble of keeping 1. You can download the final AGP 3. The ram I last used was 2x Crucial. Looking through chipset docs and then digging through a register reader ag a bit reinventing the wheel.

AGP4x + VIA Chipsets Fix

In the center of the socket is a thermo-sensor, though it shows not so exact data as that of Pentium III processor kt133aa it’s integrated in the CPU. The boards with ATA support.

Of course, the boards with possibility to install ATAcompatible HDD existed also for AMD processors but it agpp achieved at the expense of usage of chips from third manufacturers such as CMD or Highpoint what couldn’t help telling upon the system cost. Pulse voltage converters are equipped with ten capacitors of and uF, what can help in overclocking the board.

EPoX EP-8KTA3+ – motherboard – ATX – Socket A – KT133A

I dunno how deep you want to get into it, but have you ,t133a any of the other usual tweaks with that particular combo, like different 4-in-1 drivers, setting the AGP speed to 2X, upping the Vcore and drive strength by a notch, etc.? What could the manufacturers offer for Intel processors? The same thing we can say about its rival Iwill KAR, the chipset is new as well. There’s no such thing as a 3.


Find other tech and computer products like this over at Amazon UK’s website. Consumer-oriented video cards which need to draw lots of power usually require you to plug in a disk drive power supply cable. It was followed by AGP 2. You will see if the Memory Interleave Enabler works if the memory performance goes up, which also increases 3dmark scores.

When I swtiched over to CL2 ram, sandra showed me about mbps theoretical increase, but in far cry I went from an average of 27 to 36 fps. AGP compatibility for sticklers: Since the personnel consists of experienced specialists the company products were always qualitative: Power supply information Compatibility issues for ATX power supplies and motherboards A short history of PC power supply voltage rails So what’s all this rubbish about multiple 12 volt rails?